Maytag Washing Machine Stops Mid Cycle Full of Water and Wont Start Again

Download Article

Download Article

Washing machines are complicated, simply when yours stops mid-cycle in that location are a couple of likely culprits that can be fixed without too much special expertise. If in that location was a power surge, try a main reset. If you are having trouble with the water level, test the water control switch. If your car fills upwards and tumbles, but does non spin, then yous should check the lid switch.

1. one

   Unplug the washing machine. Often washing auto malfunctions are acquired an electrical fasten or figurer malfunction. In these cases, unplugging the washing machine is the first step toward resetting the computer and fixing the issue.^{[1] [2]}

   • Usually this should exist the beginning thing you effort. It is less invasive or strenuous than other methods of fixing a malfunctioning washer.

2. 2

   Wait for a minute and and then plug the washing machine back in. Do not plug the washing machine back into the outlet immediately. Allow it to sit unplugged for a infinitesimal.^[3]

   Ad

3. 3

   Open up and close the door several times quickly. Try to open up and close the door 6 times in a bridge of 12 seconds. Many washing machines are set upwards so that this signals the figurer to reset.^[4]

4. 4

   Test the washing automobile. To see if the washing machine is fixed, set information technology on "minor load" and allow information technology to run without anything inside. If it runs through its full cycle, it is safe to brainstorm washing clothes in it once more.

   Advertisement

1. one

   Discover the lid switch. The lid switch is the part on acme-loading washing machines, that sends the machine a indicate indicating that the door is closed and that information technology is condom for the machine to run. It should be an ellipsoidal hole that is aligned and so that a rod on the inside of the door will fit into information technology.^[5]

   • Considering this part takes a lot of wear and tear, it is prone to break. Thus, it is one of the most common reasons why washing machines stop at the spin bike.

2. 2

   Inspect the lid switch. Y'all tin can often estimate from appearance and bear on whether the lid switch is cleaved. The switch should be level with the top panel that it is on. If it sags, it is probable broken.

   • Similarly, you can touch the lid switch to see if the spring underneath is functioning properly. If yous printing down on the lid switch and it does not give or bound back into place, then there is likely a problem with the lid switch.^{[half dozen]}

3. three

   Remove the lid switch. The process for removing a chapeau switch depends upon the model of washer. Review the teaching guide for directions on how to remove it or google "remove chapeau switch" and the model number and series number for your washing machine. When yous remove the hat switch, leave the wires attached.^[7]

   • Be sure to unplug the washing machine before unscrewing any components.

4. 4

   Test the lid switch with a multimeter. Put your multimeter on continuity mode. Notice the connector to the lid switch. Unplug information technology and place the multimeter in the two outer connectors on the lid switch so that they touch on the metal inside. Press down on the lid switch and test for continuity.^[eight]

   • The multimeter should recognize continuity when you press the lid switch downwards, as would happen if the door were closed, but should not recognize continuity if the push is not pressed down.

5. 5

   Society a new lid switch. Lid switches tin be purchased online. They typically toll $x-20. Telephone call your manufacturer and tell them the model number of the washing machine, so that they tin direct you to lid switches that are compatible with your machine.

6. 6

   Supervene upon your chapeau switch. You will demand to consult the instructions for your specific model to determine how to replace the lid switch. Notwithstanding, if you take already removed the previous chapeau switch, information technology should not be besides complicated. You will need to identify the new lid switch where the old i had been, screw information technology in, and connect it to the electronic control lath as the old lid switch had been.^[9]

   • Later the chapeau switch has been replaced, you will demand to reinstall the console and plug the machine back into the wall.

   Advertising

1. ane

   Remove the control panel. The control console is the interface with most of the buttons that you use to operate your washing machine. Use a screw driver to remove the screws that agree information technology in identify.^[10]

2. 2

   Test the h2o level control valve. In that location should be a plastic tube underneath the control panel. It should be firmly plugged in. Remove this water level command valve and accident into it. The air should flow through naturally. If you lot can't exhale naturally in that location is a clog that needs to exist stock-still.^[11]

   • If the tube is unplugged, and so the washer might brainstorm to piece of work again if you lot properly reinsert it into the pressure switch.

3. three

   Clear water level control valve. If the tube seems to be clogged, fill up a turkey baster with vinegar and pump the vinegar down the tube. The vinegar volition dissolve the soapy residue and should render the washing machine to normal.^[12]

4. four

   Test the pressure switch with a multimeter. The plastic tube should connect to the pressure switch, which measures the amount of h2o in the washing machine. The pressure level switch should be a circular piece that looks a bit like a gear, continued to a tube. It is generally directly underneath the command panel. Disconnect the wires and plug a multimeter in to check for continuity.^[13]

   • At that place are three split plugs, which also ways that there are three pairs of connections to exam with the multimeter. Test each of these pairs separately. There should be connectivity between all of the pairs.
   • If the washing machine isn't filling up or is filling up with likewise much water, that is a good sign that there is an issue with the pressure switch or water level control valve.

5. v

   Replace the pressure switch according to specifications. Each make and model will have its ain unique method for replacing the pressure switch. If your test establishes that the pressure switch is the issue, check the instruction manual for directions on how to supervene upon information technology.

   Advert

Add New Question

• Question

  Is at that place anything else I can try?

  

  Homer Flores is an Apparatus Repair Specialist and Training Managing director at PreFix, a dwelling house maintenance visitor out of Austin, Texas. With over fifteen years of experience, Homer specializes in home comeback, remodeling, and structure. Homer'due south dedication to the PreFix mission of providing hassle-free one-end-store service for habitation care, in addition to their completion of the Upper-case letter Factory and Techstars Accelerators, has contributed to their growth of service to over fifty cipher codes throughout the greater Austin area.

  

  Apparatus Repair Specialist

  Adept Reply

  Check to make sure that the bleed hose is not inserted too far into the drain pipe at the wall. The tube only needs to get in about half dozen inches. After that, check the washing machine drain filter—it'due south usually behind a modest console to the left of the door. Be conscientious, every bit pulling the drain filter will dump whatever water is still in the unit of measurement onto the floor.

• Question

  Why does my washing car terminate filling upwardly with h2o?

• Question

  How do I prepare a washing machine that runs for a few minutes then stops?

  

  You can do a master reset, gear up the chapeau switch, or fix the water level control.

Inquire a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

Video

About This Article

Article Summary X

To fix a washing automobile that stops mid-cycle, endeavour a master reset past first unplugging the washing car to reset the computer. Later 1 infinitesimal, plug your machine back in, then open up and shut the door 6 times in 12 seconds to signal the computer to reset. To see if the machine is fixed, set information technology on "modest load" with nothing inside, and encounter if it runs through the unabridged cycle with no problems. To learn how to fix a water level control malfunction, keep reading!

Did this summary help you?

Thanks to all authors for creating a page that has been read 227,673 times.

Did this commodity help you?

fraisedonvorged.blogspot.com

Source: https://www.wikihow.com/Fix-a-Washing-Machine-That-Stops-Mid%E2%80%90Cycle

Share this post